Smartthings and SMS Remote control for Outlander PHEV

SMS and Smartthings application wrapper over phevctl

Features:

• can work over sms without smartthings
• receive PHEV errors over SMS
• receive Theft Alarm Notifications (if the theft alarm is enabled in the ETACS )
• switch on/off condition/heater
• receive warning message from the remote EV and send it in push Notification.
• send Notification "Pre A/C has stopped. Possible causes of this are as follows: Door is Open. Main battery level is Low. Drive Battery temperature is Low."
• change mode of air conditioner: heater/cool/windscreen for 10/20/30 mins,
• show battery level
• support google home
• check if doors are closed
• Thermostat Operating State
• Support SMS if use mikrotik LTE/huawei e3372h-320(CL4E3372HM)
• support wifi EVSE (Electric Vehicle (EV) Charging Stations)
• SMS commands

comparison of installation types

Cloud Installation

• cloud installation
• hetzner cloud
• scaleway cloud

Without cloud installation

• control over SMS without smartthings
• Local Network Installation(under NAT)
• Run without cloud and without Smartthings Hub

Outlander PHEV Registration

• First need to register your phone on the original application Android or Apple or (Modified application)[https://github.com/vzakharchenko/remote-ctrl-gsm]
• start Smartthings-phevctl Server
• open server and enter your phone mac.

Installation Steps

1. Install Server using Docker or raspberry Pi zero or Manual Installation
2. create Device Handler
3. create smartapp
4. Configure smartthings application on android or apple
5. Get "Smartthings Application Id" and "Smartthings Application Secret"
6. Configure Server
7. Add Smartthings devices

Server Docker Installation

• Install docker

sudo su
curl -sSL https://get.docker.com | bash
usermod -aG docker $USER

• Supported Architectures: amd64,x86-64,arm64,ppc64le,arm/v7

docker -d run --name=smartthings-phevctl  -p 8080:8080 -p 8099:8099 -p 8098:8098 --restart=always vassio/smartthings-phevctl

or

echo "{}">/opt/remote-ctrl-gsm.json
docker -d run --name=smartthings-phevctl  -p 8080:8080 -p 8099:8099 -p 8098:8098 -v /opt/config/remote-ctrl-gsm.json:/opt/remote-ctrl-gsm.json --restart=always vassio/smartthings-phevctl

Raspberry Pi Zero installation

1. Download Raspberry Pi OS Lite
2. write the Raspberry Pi OS image to the SD card using balenaEtcher or analog
3. write empty "ssh" and wpa_supplicant.conf files on sdcard (boot)
4. install phevctl, node(>=12) and smartthings-phevctl

sudo su
apt-get upgrade -y && apt-get -y install build-essential cmake git python3-distutils
mkdir /opt/phevctl
cd /opt/phevctl && git clone https://github.com/papawattu/msg-core
cd /opt/phevctl &&  git clone https://github.com/vzakharchenko/phevcore.git
cd /opt/phevctl && git clone https://github.com/DaveGamble/cJSON.git
cd /opt/phevctl && git clone https://github.com/vzakharchenko/phevctl
cd /opt/phevctl/cJSON && mkdir build && cd build && cmake .. && make && make install
cd /opt/phevctl/msg-core && mkdir build && cd build && cmake .. && make && make install
cd /opt/phevctl/phevcore && mkdir build && cd build && cmake .. && make && make install
cd /opt/phevctl/phevctl && mkdir -p build && cd build && cmake .. && make
rm -f /usr/bin/phevctl
ln -sf /opt/phevctl/phevctl/build/phevctl /usr/bin/phevctl
curl -o- https://raw.githubusercontent.com/nvm-sh/nvm/v0.37.2/install.sh | bash
source ~/.bashrc
nvm install --lts
# You can go drink coffee)
npm i pm2 -g
env PATH=$PATH:/usr/bin pm2 startup systemd -u root --hp ${HOME}
pm2 startup -u root
npm i smartthings-phevctl -g
pm2 start `npm root -g`/smartthings-phevctl/smartthings-phevctl.js
pm2 save

Server Manual Installation

sudo su
apt-get upgrade -y && apt-get -y install build-essential cmake git
mkdir /opt/phevctl
cd /opt/phevctl && git clone https://github.com/papawattu/msg-core
cd /opt/phevctl &&  git clone https://github.com/vzakharchenko/phevcore.git
cd /opt/phevctl && git clone https://github.com/DaveGamble/cJSON.git
cd /opt/phevctl && git clone https://github.com/vzakharchenko/phevctl
cd /opt/phevctl/cJSON && mkdir build && cd build && cmake .. && make && make install
cd /opt/phevctl/msg-core && mkdir build && cd build && cmake .. && make && make install
cd /opt/phevctl/phevcore && mkdir build && cd build && cmake .. && make && make install
cd /opt/phevctl/phevctl && mkdir -p build && cd build && cmake .. && make
rm -f /usr/bin/phevctl
wget -qO- https://getpm2.com/install.sh | bash
env PATH=$PATH:/usr/bin pm2 startup systemd -u ${currentUser} --hp ${HOME}
npm i smartthings-phevctl -g
pm2 start `npm root -g`/smartthings-phevctl/smartthings-phevctl.js
pm2 save

Smartthings installation

Create Custom DHT

1. open https://graph.api.smartthings.com/
2. open your location/ or create a new one
3. open "My Device Handler" and "create New Device Handler"
4. select from code and add [Outlander PHEV Action.groovy](./dht/Outlander PHEV Action.groovy), [Outlander PHEV Battery.groovy](./dht/Outlander PHEV Battery.groovy), [Outlander PHEV Thermostat.groovy](./dht/Outlander PHEV Thermostat.groovy) and [Outlander PHEV Doors.groovy](./dht/Outlander PHEV Doors.groovy)
5. click save

Create SmartApp

1. open https://graph.api.smartthings.com/
2. open your location
3. create a new SmartApp
4. select from code and add remote-ctrl-gsm.groovy
5. open smartapp application and click "App Settings"
6. enable "OAuth"
7. Save and publish application

Configure Smartthings application

1. open smartthings application in Phone Android or Apple
2. select location
3. add SmartApp
4. add "remote-ctrl-gsm"
5. set IP and port of server and click save

Get "Smartthings Application Id" and "Smartthings Application Secret"

1. open https://graph.api.smartthings.com/
2. select smartapps in your location
3. select your smartapp
4. get "Smartthings Application Id" and "Smartthings Application Secret" from the page

Configure Server

1. open server http://<IP>:8080
2. default login/password: admin/admin
3. configure "Smartthings Application Id", "Smartthings Application Secret" and mac address
4. click save

Add a new Smartthings device

1. select devices->add Device
2. Device will be appear om Smartthings App

Local Network Installation(under NAT)

• install [Smartthings Hub)[https://www.samsung.com/us/smart-home/smartthings/hubs/] on location.
• during installation smartapp select hub.

Run without cloud and without Smartthings Hub

• Configure Smartthings application without cloud and hub
• during installation smartapp select "Setup my devices without cloud".

Authentication

Local authentication (default)

default login/password: admin/admin

change password for user

add a new User

Keycloak authentication

restart Application

Keycloak authorization

restart Application

Thermostat operation state

Push Notification

EVSE Electric Vehicle (EV) Charging Stations

Scripts for energy star charging stations

• Slow charging(slowCharge.sh)

curl --header "application/x-www-form-urlencoded"   --request POST   --data 'cur_set=7&charge_start=1&adaptive_mode_status=1&adaptive_mode_voltage=220&timer=0&timer_start=0'   http://192.168.4.1/ajax

• Normal charging(fastCharge.sh)

curl --header "application/x-www-form-urlencoded"   --request POST   --data 'cur_set=16&charge_start=1&adaptive_mode_status=0&adaptive_mode_voltage=220&timer=0&timer_start=0'   http://192.168.4.1/ajax

• Disable charging(disableCharge.sh)

curl --header "application/x-www-form-urlencoded"   --request POST   --data 'cur_set=7&charge_start=0&adaptive_mode_status=1&adaptive_mode_voltage=220&timer=0&timer_start=0'   http://192.168.4.1/ajax

• Mikrotik Configuration

/interface wireless security-profiles
add authentication-types=wpa2-psk group-ciphers=tkip mode=dynamic-keys name=EVSE supplicant-identity=MikroTik unicast-ciphers=tkip wpa-pre-shared-key=<EVSE_PASSWORD> wpa2-pre-shared-key=<EVSE_PASSWORD>
/interface wireless
set [ find default-name=wlan1 ] disabled=no frequency=2447 mode=station-pseudobridge name=EVSE_CHARGER security-profile=EVSE ssid=<EVSE_SSID>

/interface bridge
add dhcp-snooping=yes fast-forward=no igmp-snooping=yes name=bridgeEVSE
/interface bridge port
add bridge=bridgeEVSE broadcast-flood=no edge=no-discover interface=EVSE_CHARGER multicast-router=disabled trusted=yes unknown-multicast-flood=no unknown-unicast-flood=no
/interface bridge settings
set allow-fast-path=no

/ip dhcp-client
add add-default-route=no disabled=no interface=bridgeCar use-peer-dns=no use-peer-ntp=no
add add-default-route=no disabled=no interface=bridgeEVSE use-peer-dns=no use-peer-ntp=no

add authorization for EVSE Charging

• start proxy application

npm i pm2 -g
env PATH=$PATH:/usr/bin pm2 startup systemd -u root --hp ${HOME}
pm2 startup -u root
npm i smartthings-phevctl -g
pm2 start `npm root -g`/smartthings-phevctl/evse-proxy.js
pm2 save

• configure evse-proxy

nano ~/.remote-ctrl-gsm/config.json

{
 "evseServer": {
  "/": "https://192.168.4.1",
  "style.css": "https://192.168.4.1/style.css",
  "es.js": "https://192.168.4.1/es.js",
  "ajax": "https://192.168.4.1/ajax"
 },
 "users": [
  {
   "id": "0",
   "username": "admin",
   "password": "admin"
  }
 ],
 "port": 8011,
 "role":"<KEYCLOAK_REALM>:<KEYCLOAK_CLIENT>"
}

• Keycloak authorization example keycloak.json:

{
  "realm": "<REALM>",
  "auth-server-url": "https://<KEYCLOAK_URL>/auth/",
  "ssl-required": "external",
  "resource": "<CLIENT_ID>",
  "credentials": {
    "secret": "<CLIENT_SECRET>"
  },
  "confidential-port": 0
}

Keycloak security role:

{
 "evseServer": {
  ...
 }
 ],
 "role":"<KEYCLOAK_REALM>:<KEYCLOAK_CLIENT>"
}