Package Exports

homebridge-http-sensors-switches
homebridge-http-sensors-switches/dist/index.js

This package does not declare an exports field, so the exports above have been automatically detected and optimized by JSPM instead. If any package subpath is missing, it is recommended to post an issue to the original package (homebridge-http-sensors-switches) to support the "exports" field. If that is not possible, create a JSPM override to customize the exports field for this package.

Readme

Homebridge Platform Plugin

HTTP Sensors and Switches

This plugin communicates with your devices over HTTP or MQTT. Currently it supports Switches, Temperature/Humidity and Motion sensor.
Simple Discord Webhooks available in Switches

🕺 Motion Sensor

[!NOTE]
HTTP - Read status (true/false) from JSON - {"Motion": true}
MQTT - Read status (true/false)

💡 Switch

[!NOTE] HTTP - Read Status (On/Off), Turn ON (url), Turn OFF (url)
MQTT - Turn ON/OFF | Values: On = 1, Off = 0
Discord Webhook publishes switch status to your Discord channel

[!TIP] If you don't have Manual switch and you don't mind when Homebridge is rebooted, your device is going to be set as OFF then you don't have to use Parameter urlStatus.

How to setup Discord Webhooks: link

[!IMPORTANT] Use HTTP or MQTT not both for same accessory.

Parameters required in Config:

deviceType = 'Switch',
deviceName = 'Name your Accessory',
deviceID = 'Put something unique / chars and numbers',
urlON = 'URL that triggers your device to change state to ON',
urlOFF = 'URL that triggers your device to change state to OFF'

[!CAUTION] Parameter: urlStatus = 'url points to JSON with device status' when is set it will bind Accessory to 5 sec check status interval

{
    "POWER": "ON"
}

🌡️ Temperature and Humidity sensor

[!NOTE] Sensor - Read JSON Or MQTT for Temperature, Humidity

[!TIP] Parameters required in Config:

deviceType = 'Sensor',
deviceName = 'Name your Accessory',
deviceID = 'Put something unique / chars and numbers',

For JSON read use param sensorUrl:
sensorUrl = 'JSON file containing sensor readings (temperature, humidity)',

For MQTT use param mqttBroker:
mqttBroker = 'URL of MQTT Broker'

[!IMPORTANT] MQTT is just an basic implementation, no encription etc.

Sensor JSON file example

{
    "t": "29.37",
    "h": "48.26",
    "p": "1001.33"
}

⚙️ Config example

{
    "bridge": {
        "name": "Homebridge xxxx",
        "username": "xx:xx:xx:xx:xx:xx",
        "port": 51576,
        "pin": "xxx-xx-xxx",
        "advertiser": "bonjour-hap"
    },
    "platforms": [
        {
            "name": "Config",
            "port": 8581,
            "auth": "form",
            "theme": "auto",
            "tempUnits": "c",
            "lang": "auto",
            "noFork": true,
            "standalone": true,
            "platform": "config"
        },
        {
            "platform": "HttpSensorsAndSwitches",
            "name": "Stergo",
            "description": "Http all in one place",
            "devices": [
                {
                    "deviceType": "Sensor",
                    "deviceID": "896543287",
                    "deviceName": "Attic",
                    "deviceManufacturer": "NameTheManufacturer",
                    "deviceModel": "DHT",
                    "deviceSerialNumber": "203ab773-d5cd-42ww-b531-a98bba0e4444",
                    "deviceFirmwareVersion": "v1.4.0",
                    "sensorUrl": "http://192.168.1.74/mesures.json",
                    "temperatureName": "t",
                    "humidityName": "h",
                    "updateInterval": 60000
                },
                {
                    "deviceType": "Switch",
                    "deviceID": "1234578",
                    "deviceName": "Night Light",
                    "deviceManufacturer": "Stergo",
                    "deviceModel": "Switch",
                    "deviceSerialNumber": "203ab773-d5cd-42a2-b531-a98bba0e4444",
                    "deviceFirmwareVersion": "0.4.0",
                    "urlON": "http://192.168.1.77/POWER?state=ON",
                    "urlOFF": "http://192.168.1.77/POWER?state=OFF",
                    "urlStatus": "http://192.168.1.77/POWER",
                    "stateName": "POWER",
                    "onStatusValue": "ON",
                    "offStatusValue": "OFF"
                },
                {
                    "deviceType": "Sensor",
                    "deviceID": "65432258",
                    "deviceName": "Balcony",
                    "sensorUrl": "http://192.168.1.72/mesures.json",
                    "temperatureName": "t",
                    "updateInterval": 300000
                },
                {
                    "deviceType": "Switch",
                    "deviceID": "21wqwweqwee65432258",
                    "deviceName": "Relay",
                    "mqttBroker": "192.168.1.200",
                    "mqttPort": "1883",
                    "mqttSwitch": "iot/things/StergoTestSwitch/switch1",
                    "mqttUsername": "testuser",
                    "mqttPassword": "testuser",
                    "discordWebhook": "https://discordapp.com/api/webhooks/XXXXX",
                    "discordUsername": "SmartHome",
                    "discordAvatar": "",
                    "discordMessage": " is "
                },
                {
                    "deviceType": "Sensor",
                    "deviceID": "65432258",
                    "deviceName": "Balcony",
                    "mqttBroker": "192.168.1.200",
                    "mqttPort": "1883",
                    "mqttTemperature": "qiot/things/Attic/Temperature",
                    "mqttHumidity": "qiot/things/Attic/Humidity",
                    "mqttUsername": "testuser",
                    "mqttPassword": "testuser"
                }
            ]
        }
    ]
}

⚙️ Config params

Compromise: Switch accessory, in order to work properly getStatus is bind in 5 sec interval. This is for passive devices not pushing their status. I have several devices built by my self like ESP8266 with relay and I'm just switching state. I have JSON file showing status:

{
    "POWER": "ON"
}

[!IMPORTANT] Homebridge v2.0 Information

This template currently has a

package.json -> engines.homebridge value of "^1.8.0 || ^2.0.0-beta.0"

package.json -> devDependencies.homebridge value of "^2.0.0-beta.0"

This is to ensure that this plugin will build and run on both Homebridge v1 and v2.

[!IMPORTANT] Node v22 Information

This template currently has a

package.json -> engines.node value of "^18.20.4 || ^20.16.0 || ^22.5.1"

This plugin should be supporting Node v22 from October 2024.